|
|
Back to UserFriendly Strip Comments Index
| Attn: UFicle, cdrecord under RHEL4? |
by DesiredUsername |
2009-03-31 17:19:12 |
Hi,
I'm trying to relearn how to burn CDRs under Linux. I have an ISO file that I've burned using imgburn under Windows just fine. Now I'm trying to do it using RHEL and cdrecord. It's the version that comes with RHEL4 (which is up2date, but kernel=2.6.9-67.0.15.ELsmp, x86_64, Opteron 2218HE).
The command I'm using is:
cdrecord dev=ATA:0,0,0 -dao -v speed=8 File.iso
I've also tried with fs=512M, same thing.
It works fine with -dummy.
Any ideas?
Thanks!
Cdrecord-Clone 2.01-dvd (--) Copyright (C) 1995-2004 Jörg Schilling
Note: This version is an unofficial (modified) version with DVD support
Note: and therefore may have bugs that are not present in the original.
Note: Please send bug reports or support requests to http://bugzilla.redhat.com/bugzilla
Note: The author of cdrecord should not be bothered with problems in this version.
TOC Type: 1 = CD-ROM
scsidev: 'ATA:0,0,0'
devname: 'ATA'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.8'.
cdrecord: Warning: using inofficial libscg transport code version (schily - Red Hat-scsi-linux-sg.c-1.83-RH '@(#)scsi-linux-sg.c 1.83 04/05/20 Copyright 1997 J. Schilling').
SCSI buffer size: 64512
atapi: -1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'SONY '
Identifikation : 'DVD RW AW-Q170A '
Revision : '1.70'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009
Profile: 0x002B
Profile: 0x001B
Profile: 0x001A
Profile: 0x0016
Profile: 0x0015
Profile: 0x0014
Profile: 0x0013
Profile: 0x0011
Profile: 0x0010
Profile: 0x000A
Profile: 0x0009 (current)
Profile: 0x0008 (current)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 890880 = 870 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 489 MB
Total size: 561 MB (55:39.45) = 250459 sectors
Lout start: 562 MB (55:41/34) = 250459 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 4
Is not unrestricted
Is not erasable
Disk sub type: Medium Type A, high Beta category (A+) (3)
ATIP start of lead in: -11849 (97:24/01)
ATIP start of lead out: 359848 (79:59/73)
Disk type: Long strategy type (Cyanine, AZO or similar)
Manuf. index: 25
Manufacturer: Taiyo Yuden Company Limited
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 109389
Speed set to 1411 KB/s
Starting to write CD/DVD at speed 8.0 in real SAO mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
trackno=0
BURN-Free is ON.
Turning BURN-Free off
Performing OPC...
Sending CUE sheet...
cdrecord: WARNING: Drive returns wrong startsec (0) using -150
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 1 of 489 MB written (fifo 100%) [buf 100%] 0.3x.cdrecord: Success. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 02 C9 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: F0 00 03 00 00 00 E8 0A 00 00 00 00 0C 08 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x0C Qual 0x08 (write error - recovery failed) Fru 0x0
Sense flags: Blk 232 (valid)
resid: 63488
cmd finished after 0.007s timeout 200s
write track data: error after 1460224 bytes
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
Writing time: 39.872s
Average write speed 128.9x.
Min drive buffer fill was 100%
Fixating...
Fixating time: 0.000s
cdrecord: fifo had 87 puts and 24 gets.
cdrecord: fifo was 0 times empty and 15 times full, min fill was 90%.
|
|
[ Reply ] |
|
Have you tried the nautilus burner or k3b? (n/t) | by vdp | 2009-03-31 18:52:20 |
|
Weird. Nautilus failed, k3b succeeded. | by DesiredUsername | 2009-03-31 19:34:08 |
|
EEEEEWWWW! | by bwkaz | 2009-03-31 22:20:52 |
|
|
[Todays Cartoon Discussion]
[News Index]
|
|
